WetLook Wet Area DS

Your Subtitle text

WETLOOK ENHANCER

PRODUCT DATA SHEET & APPLICATION GUIDELINE

WL350 Gloss for Wet Areas, Pools, Fountains

PRODUCT DATA SHEET

WetLook Enhancer
WL350 Gloss for Wet Areas

Description:
WetLook Enhancer WL350 is a premium quality product for applications where fast drying, excellent durability and wet area application (pools, waterfalls) are a requisite. WL350 is a breakthrough formulation combining reactive silicone and acrylic complexes that form a high performance polymer that powerfully penetrates and adheres to the substrate. The barrier formed protects the surface for years and years and will retain its deep glossy shine. The advanced polymer of silicone and acrylic resins penetrates into the substrate and securely anchors to the substrate forming an uncompromising barrier that resists penetration from water, elements in or suspended in the water such as salt and pool chemicals, oils, and more. WL350 silicone base forces deeper penetration preventing tear or peel off; additionally because it has superior penetrating properties it will withstand hydrostatic lifting much better than a acrylic based coating.

Features and Benefits:

Durable, exceptionally long lasting: high penetration formulation

Incredible rich, vibrant, enhanced wet look, gloss or natural

Outstanding strong, hard, mar and scratch resistant finish

Forms a waterproof barrier, resistant to many chemical, salt, organic stains, oils, vehicle fluids and contaminant penetration

Exceptional coverage

Non-fading, strong resistance to UV rays; non-yellowing

Maintains gloss; fast drying; low odor

Strong bonding – exceptionally high resistance to hydrostatic pressures

Substrates and Surfaces
Use on previously coated or uncoated, vertical or horizontal, interior or exterior surfaces such as pavers, concrete, Mexican tile and unglazed tiles, brick, aggregate, natural and artificial stone, masonry, stucco, marble, terrazzo, granite, wood and many metals.
Use around pools, fountains, showers and water areas.
ALWAYS TEST each type of surface for penetration, appearance and protective ability before overall application. Let test area dry before inspection.
Preparation
Surface to be treated must be clean and dry. Remove dirt, oil, grease, paint, waxes, efflorescence and surface sealers.
Let new concrete cure 28 days before treating.
Ensure fresh air entry and cross ventilation during application and drying. Extinguish all flames, pilot lights and other potential sources of ignition during use and until all vapors are gone. Protect passersby, building occupants, people, vehicles, property, plants, painted surfaces and all non masonry surfaces from product, residue, splash, fumes and wind drift. Use polyethylene or other proven protective material.

Application
Before applying read all sections above. Do not dilute or alter. ALWAYS TEST a small area of each surface to confirm suitability and desired results before starting overall application. Test with the same equipment that will be used in application.

Apply a thin, even coat of WetLook Enhancer with a low-pressure sprayer not to exceed 1.0 - 1.5 dry mills per coating. Do not apply thick coating as pooling can result in depressions.
Porous Substrates: two thin applications will generally result in a uniform appearance on porous surfaces. Additional coats may be desired depending on actual porosity and appearance desired.
Non-porous Substrate: one to two thin applications.
Allow 30 minutes to1 hour between coats or until surface is dry with pressure touch.
Exceeding 3 mils total dry-film build up may affect overall durability.
Protect from rain for one hour after application.

Typical Physical Properties

COLOR: Transparent
GLOSS: Full
W.T./GALLON: 7.75 lbs/gal
VISCOSITY AT 77⁰ F 80 KU
SHELF LIFE: 3 Years
SOLIDS BY WEIGHT: 33%
CHEM RESISTANCE: Very Good
FLASH POI:NT 80⁰ F, TCC
V.O.C.: 4.4
DRY TIME @ 77⁰ F, 55% R.H.
   Touch: 10-15 Minutes
    Handle: 30 min - 1 Hour
    Re-coat: 30 min - 1 Hour
FILM THICKNESS
    Wet: 2.5 - 4.0 mils
    Dry: 1.0 - 1.5 mils
CLEANING OF EQUIPMENT
    Xylene Flush

Surface and Air Temperature
Temperatures should be 50-90⁰(10-32⁰C). Use only in well ventilated areas.

Dilution
Apply as packaged. Do not dilute or alter, or use for applications other than as specified.

Coverage / Dry Time / Shelf Life

Coverage varies based on porosity and texture. Always test.

Theoretical coverage: 525 sq. ft /gal. @ 1 mil dry film thickness (dft.)

Porous Surfaces: great coverage but will vary depending on porosity of the surface;

Non-Porous Surfaces: 400 – 525 sq. ft. / gallon

Shelf Life: 12 Months if unopened and stored in a cool dry area. Shelf life will be shortened once opene
Equipment
Because of the short dry time this product is best applied with low pressure spray equipment. The product can alternately be applied with a fine natural bristle brush; care should be taken to avoid brush marksd.

Cleanup
Clean tools and equipment immediately with Xylene Flush. Container may retain residues. Keep from ignition sources. Do not reuse container.

Maintenance
Sweep and damp mop treated surfaces frequently to prevent abrasion from grit and dirt. Remove heavy soiling with a surface cleaner.

Approx. Shipping Weights
1 gallon (18.9L) 7.75 lbs
5 gallon pail (94.5L) 38.75 lbs

CAUTION: Harmful if swallowed. Eye, skin and respiratory irritant.
If swallowed DO NOT induce vomiting. Call physician immediately. Eye contact: flush with large amounts of room temperature water for 15 minutes. Skin contact: wash thoroughly with soap and water. Irregular or stopped breathing: administer oxygen, give artificial respiration. Get medical attention immediately. Do not breath vapors or spray mist. Wear respirator approved by NIOSH.

USE WITH ADEQUATE VENTILATION - KEEP OUT OF REACH OF CHILDREN.

For limited warranty and disclaimer information contact Serveon Specialty Chemicals.

Request MSDS for additional information.